They not only take care of the hour by hour and day by day adjustments required for changes in tide and water levels but are also on hand in the event of unpredictable and potentially disastrous weather bombs, tidal surges and flash floods which effect coastal and inland waterways and lakes from time to time. Pile Ring sits on the surface of the water around a mooring pile. Mooring ropes from your boat or craft are tied to the Pile Ring instead of the pile. The Pile Ring floats up and down the mooring pile at the same rate as your boat or craft and as such never needs adjusting. Your boat will always have tight and/or perfectly adjusted lines.
Model | Type | Dimensions | Weight | Colours |
---|---|---|---|---|
PR400 | One-Piece | 25" x 25" x 6" | 18Lbs | Black / Orange |
PR500 | One-Piece | 30" x 30" x 8" | 24Lbs | Black / Orange |
PR550 | One-Piece | 34" x 34" x 7" | 30Lbs | Black / Orange |
PR350-2 | Two-Piece | 26" x 26" x 10" | 11Lbs | Black / Orange |
PR475-2 | Two-Piece | 34" x 34" x 10" | 13Lbs | Black / Orange |
PR750-4 | Four-Piece | 42" x 42" x 12" | 49Lbs | Black / Orange |
1. Integrated 19mm (3/4”) Solid Stainless Steel HoopA high-grade marine quality stainless steel hoop provides an extremely secure fastening point. The marine pile or the rope will give way long before the ring is even slightly distorted.
2. Super Tough Roto-Moulded Polyethylene ShellThe solid stainless steel hoop is kept well out of the water by the buoyant floating device. It also serves to protect the marine pile and boat from damage by acting as a float and fender.
3. Unique Space Saving Nesting DesignThe marine Pile Rings are cleverly designed to stack on top of each other. This makes them easy to handle and ship. It also provides space-saving storage for marinas.
4. Closed Cell Foam FillingIn addition to providing extra buoyancy, the closed cell foam prevents water ingress and ensures it is unsinkable even if it was cut in half.
5. Multiple Strong Mooring PointsThe 4 strong pile ring tie-off points give a wide range of mooring configuration options for marinas, pontoons, and rivers, etc.
1. Unique Hinge & Bolt DesignThe Patent Pending design provides for the easiest of installations. Designed specifically to be used in areas where access is limited such as under a pier or wharf or in situations where temporary mooring is required.
2. Super Tough & Unique Roto-Moulded Polyethylene ShellThe pile rings are constructed of a new grade of flexible and super tough polyethylene giving it durability and longevity and providing superior buoyancy. It also serves to protect the marine pile and boat from damage by acting as a float and fender.
3. Integrated 50MM (2″) Rope RecessThe recess can take multiple mooring lines or ropes up to 50mm (2″) and is finished to a smooth surface to prevent chafing of the rope and protect it from impact.
4. Twenty Tonne Bollard PullThe multi-piece Pile Rings are designed to flex. The inner and outer walls touch under stress and the ultimate strength is achieved. Mooring risk is transferred to the mooring line and the pile. Our Pile Rings have been independently tested to a sustained 20 tonne bollard pull.
5. Strong Fasteners & Hinge PinThe multiple pieces are joined together using unique stainless steel hinge pins. They hold and lock the whole Pile Ring in position with a single marine grade 316 stainless steel bolt on each side. The shape of the pins prevents contact with your boat hull.
1. Unique Multi-Piece DesignDesigned specifically to be used in areas where access is limited such as under a pier or wharf or for situations where temporary mooring needs to be provided quickly.
2. Super Tough Roto-Moulded Polyethylene ShellThe pile rings are constructed of super tough thick walled polyethylene giving it durability and longevity and providing superior buoyancy. It also serves to protect the marine pile and boat from damage by acting as a float and fender.
3. Integrated 50MM (2″) Rope RecessThe recess can take ropes up to 50mm (2″) and is finished to a smooth surface to prevent chafing of the rope and protect it from impact.
4. Innovative Modular Stacking SystemThe multi-piece Pile Rings are cleverly designed to be used individually or stacked on top of each other when additional buoyancy is required or where floating, heavy duty pile protection is needed.
5. Strong Fastenings & SpacersThe multiple pieces are joined together using marine grade 316 stainless steel bolts and the spacers act as non-compressible washers and rope guides. Interlocking spacers are available for stacking.
ONE-PIECE
TWO-PIECE
MULTI-PIECE
Colour Choice:
Colour Choice:
Colour Choice:
Colour Choice:
Colour Choice:
Colour Choice:
Pile Ring is a floating mooring device which sits on the surface of the water about a mooring pile. Mooring ropes from your boat, craft or device are tied to the Pile Ring instead of the pile. The Pile Ring floats up and down the mooring pile at the same rate as your boat or craft and as such never needs adjusting. Your boat will always have tight and/or perfectly adjusted lines even in high tides, bad weather or storm surges. You need never be caught out again.
Pile Rings take all the worry and anguish out of mooring your boat when there is the potential for inclement weather, sudden flooding, tidal anomalies, and storm surges as there is no need to tend to the lines. They are always at the right length and tension no matter what the situation. They also help to solve issues associated with berthing and docking maneuvers where wind and tide can cause sudden unexpected movement.
Pile Rings can be used to safely moor any floating boat, yacht, craft, vessel or equipment (e.g. Floating Solar Power) in any state of tide, current, weather or flood without the need for constant attention, monitoring or adjustment (within the constraints, limitations and heights of the pilings themselves).
The mooring line from the Pile Ring to your boat should be tight but not so tight that the Pile Ring starts to pull out of the water. It should remain properly afloat in a horizontal position. This provides “give” in the rope and allows the boat to ride with the waves, currents and movement of the water comfortably. As such it does not put undue strain on any ropes or marine hardware. It also ensures that the Pile Ring is not forcibly worn on one side against the piling.
N.B. Pile Rings are not designed for use on square concrete pilings as the sharp and abrasive concrete corners will wear into the polyethylene.
Single Pile Rings are rotationally moulded from high-quality virgin polyethylene (plastic) which is super strong and tough and almost indestructible. A single welded high grade 304 marine stainless steel hoop is inserted into the polyethylene float at time of moulding and this cannot be pulled out. The float is then filled with a closed cell polyurethane foam so that in the unlikely event of a puncture or leak or damage then the pile ring will still not sink.
N.B. 316 stainless steel is not used for our integrated hoop as it is not as strong as our particular grade of 304 stainless steel under these mooring conditions. The surface may display a tea-stain over time but it will not rust for a considerable number of years.
Multi-Piece Pile Rings are made using our unique grade of rotationally moulded polymer and are designed to flex a little to provide maximum strength.
We commissioned independent bollard pull tests for our multi-piece Pile Rings to a sustained 20 tonnes. The rings maintained their integrity and performance. They do flex and distort under immense pressure but no damage at all was recorded.
We have tested the single piece Pile Ring to 3 tonnes (6000lbs) direct pull using an accurate Load Cell device. To give you some idea of how strong this is – your Ropes and your actual Piles are far more likely to break before the Pile Ring gets anywhere near its maximum load.
N.B. It is not the weight of the boat that counts but the pressure exerted on the ropes, pile and Pile Ring.
Pile Ring comes in five sizes:
N.B. Please make sure to measure your pilings at all states of tide before ordering and if in any doubt then please contact us for further guidance.
Our Pile Rings are made from high quality, high grade materials and under normal usage and circumstances they should easily be lasting over ten years. Studies in New Zealand have shown many earlier designs to have lasted longer than twenty years. Please see our warranty terms and conditions for further information.
Our Pile Rings are made from high quality, high grade materials and under normal usage and circumstances they should easily be lasting over ten years. Studies in New Zealand have shown many earlier designs to have lasted longer than twenty years. Please see our warranty terms and conditions for further information.
Pile Rings themselves do not require any maintenance, however, due to the localised nature and veracity of marine biofouling in your area it may be necessary to clean the Pile Ring from time to time. Our high quality polyethylene is impenetrable to marine biofouling and does not require any anti-fouling treatment, however, slime, weed, barnacles, mussels, oysters, etc. can attach themselves over time as with any other submerged surface. It is suggested that you inspect your Pile Rings regularly to check for marine growth. If the growth is heavy it will need scraping, cleaning, or water blasting to maintain the correct buoyancy, floatation and of course appearance.
Permanently tight lines made simple and safe regardless of location
No more chafing on pilings and hardware (the leading cause of dock disasters)
Facilitates far easier dock entry/exit manoeuvres and line handling
Eliminates any need to adjust moorings lines for tidal range or weather
Environmentally friendly manufacturing process using recyclable materials
Manufactured in New Zealand from high grade materials to ISO 9001
Marine grade floatation device filled with high quality closed cell PU foam (where specified)
Pile Rings nest inside each other for better handling, storage and shipping costs
Pile Ring also acts as a non-marking fender for docks, boats and pilings
5 years with a practical life of 10+ years (subject to fair wear and tear) *please see terms & conditions for full details
Bollard pull tests of 20 tonnes on multi piece and 3 tonnes on single piece
Incredibly hard wearing & resistant to all forms of marine growth and algae
Reduced maintenance costs through constant cleaning and removal of marine growth
UV stable and weather proof in the harshest of conditions 24/7 and 365 days
Thousands of mooring pile rings already in extensive use internationally
Agricultural, industrial and commercial water reservoirs systems
The floating nature of the Pile Ring together with its four substantial tie-off points means it provides almost endless configurations and flexible options for mooring.
Customisation is not required and neither is a long list of additional product options and enhancements together with their associated and unexpected costs.
As can be seen from the examples here, Pile Rings are suitable for any mooring style and for cost-effective use in marinas, rivers, lakes, canals, and any other kind of waterway.